The numbers, and where each one comes from
Tables and references

Paper, postal, contrast and type figures, and where each one comes from

Every figure this manual uses, on one page, with its publisher named on the line. Paper and poster sizes, postal dimensions, bleed and resolution, the ADA character table in full, the contrast thresholds and the type ranges.

This is the page to come back to. Every row names who publishes the figure, because the difference between a published standard, one practitioner's recommendation and a convention somebody wrote down is the thing that tells you how firmly a number is known. Where two publishers disagree, both are printed and neither is quietly dropped.

All of these were read on 2026-11-13. Links and dates are in the resource library, and the figures that move are listed at the foot of this page.

Paper and poster sizes

NameInchesMillimetersPublished by
US Letter8.5 by 11216 by 279papersizes.org, a third-party reference
US Legal8.5 by 14216 by 356papersizes.org
Tabloid / Ledger (ANSI B)11 by 17279 by 432papersizes.org
A48.27 by 11.69210 by 297papersizes.org
A311.69 by 16.54297 by 420papersizes.org
Poster, small11 by 17279 by 432papersizes.org
Poster, medium18 by 24457 by 610papersizes.org
Poster, large24 by 36610 by 914papersizes.org

Convention These are conventional figures from a third-party reference site, not quotations from a standard. The underlying standards are ANSI/ASME Y14.1 for the US sizes and ISO 216 for the A series, and this manual did not read either document. The sizes are stable and widely agreed; the point of saying this is that if a figure here mattered for a contract, the standard is where you would go.

Yard sign sizes. No published source sets one. A commonly cited range runs from about 12 to 40 inches with no sizing standard behind it. The practical instruction is in Signs: measure the wire frame you bought.

USPS card and letter dimensions

MeasureCard pricesLetter-sizeSection
Minimum height3-1/2 in3-1/2 inDMM 201.1.2.1 / 201.1.1.1
Minimum length5 in5 inDMM 201.1.2.1 / 201.1.1.1
Minimum thickness0.007 in0.007 inDMM 201.1.2.1 / 201.1.1.1
Maximum height4-1/4 in6-1/8 inUSPS Sizes for Postcards / DMM 201.1.1.1
Maximum length6 in11-1/2 inUSPS Sizes for Postcards / DMM 201.1.1.1
Maximum thickness0.016 in1/4 inUSPS Sizes for Postcards / DMM 201.1.1.1
Thicker minimum, once the piece is over 4-1/4 in high or 6 in long0.009 inDMM 201.1.2.1, 201.2.1.1
Aspect ratio, length divided by height1.3 to 2.5 inclusiveDMM 201.3.7
Weight cap for a machinable letter3.5 ozDMM 201.1.1.2
Address portion, vertical split on a cardAt least 2-1/8 in wideDMM 201.1.2.7
Address portion, horizontal split on a cardAt least 1-1/2 in highDMM 201.1.2.7
Minimum paper for an enveloped or four-side-sealed letter50 lb book-grade basis weight or equivalentDMM 201.3.2

Regulation Length is the side parallel to the address; height is the other one. A piece outside the 1.3-to-2.5 range pays nonmachinable letter prices (DMM 201.2.1.2), and USPS states that a piece missing the postcard dimensions is considered a letter and charged letter-size postage.

A conflict we found, printed rather than resolved

DMM 201.1.2.1 also contains a line giving a card maximum of not more than 6 inches high, 9 inches long or 0.016 inch thick. That does not agree with the 4-1/4 by 6 inch maximum USPS prints on its Sizes for Postcards page. This manual uses the smaller pair, because it is the figure USPS publishes for the public and because a card inside it is inside both readings. If your card falls between the two, take it to a counter and ask with the piece in your hand.

What makes a piece nonmachinable (DMM 201.2.1.1): an exterior surface not made of paper; failing the 0.009 inch thickness rule for a large piece; failing the automation standards in section 3.0, which include the aspect ratio; or weighing more than 3.5 ounces. Paper window envelopes do not make a piece nonmachinable. Section 3.8 bars clasps, strings, buttons or similar closure devices on automation pieces; 3.10 prohibits rigid items such as pens, pencils, keys and bottle caps inside; 3.12.1 requires the piece to bend around an 11-inch drum under 40 pounds of belt tension.

No prices appear anywhere in this manual, because no USPS page it read carried one. Will this card mail? tells you the price category; a counter or usps.com gives the figure.

Bleed, safe area and resolution

FigureValuePublished by
Bleed, small format0.125 in (1/8 in) on every sideSmartpress, and 4OVER4.COM independently
Bleed, large format (signs, posters, banners)0.25 in (1/4 in)Smartpress only
Safe area, standard0.125 in inside the trimSmartpress, and 4OVER4.COM independently
Safe area, with a border round the edge0.25 in inside the trimSmartpress; 4OVER4.COM says 0.25 in for a text-heavy piece
Resolution, small format300 DPI at the finished sizeSmartpress; 4OVER4.COM states 300 PPI at final size
Resolution, large format150 PPI at the finished sizeSmartpress only
Color modeCMYKSmartpress; 4OVER4.COM asks for CMYK for offset and digital work

Product-specific These are two printers' published specifications, not an industry standard. Stage 1 of this manual's research could reach no printer specification page with figures other than Smartpress; the second, 4OVER4.COM, was found in the build pass and agrees with it on every small-format figure. Two independent printers agreeing is why the small-format numbers are stated as a starting point. The two large-format figures have one publisher. Ask your own printer, and ask a copy shop or a library printer what it can actually do.

A home printer cannot print to the edge of a sheet. Every machine has an unprintable band and it differs by model; find yours by printing a rectangle outlined at the page edge and measuring where the line landed. Flyers and posters has the two ways round it.

Page setup and resolution applies all of these to a finished size.

ADA Table 703.5.5, in full

Limits

The 2010 ADA Standards for Accessible Design apply to signs in buildings and facilities covered by the Americans with Disabilities Act. They are not a general legibility rule. Where this manual applies Table 703.5.5's rate to a flyer, a yard sign or a slide, it is borrowing a published rate and says so. No standard this manual found sets a minimum letter height for a yard sign, a flyer or a slide. Where the Act does apply to a building, these are legal requirements and a code official settles them; this manual certifies nothing.

Height of characters above the floor, from the baselineHorizontal viewing distanceMinimum character height
40 in to 70 in inclusiveLess than 72 in5/8 in
40 in to 70 in inclusive72 in and greater5/8 in, plus 1/8 in per foot of viewing distance above 72 in
Greater than 70 in to 120 in inclusiveLess than 180 in2 in
Greater than 70 in to 120 in inclusive180 in and greater2 in, plus 1/8 in per foot of viewing distance above 180 in
Greater than 120 inLess than 21 ft3 in
Greater than 120 in21 ft and greater3 in, plus 1/8 in per foot of viewing distance above 21 ft

Regulation Publisher: U.S. Access Board, 2010 ADA Standards, section 703.5.5. Character height is measured on an uppercase I, from its baseline to its top. Viewing distance is the horizontal distance between the character and an obstruction preventing further approach.

The rest of section 703, for signs in its scope

RequirementFigureSection
Visual characters: finish and polarityNon-glare; light characters on a dark background, or dark characters on a light background703.5.1
Visual characters: caseUppercase, lowercase or both703.5.2
Visual characters: styleConventional in form; not italic, oblique, script, highly decorative or unusual703.5.3
Visual characters: proportionWidth of an uppercase O, 55 to 110 percent of the height of an uppercase I703.5.4
Visual characters: height above floorAt least 40 in703.5.6
Visual characters: stroke thickness10 to 30 percent of character height703.5.7
Visual characters: character spacing10 to 35 percent of character height, between the two closest points of adjacent characters, excluding word spaces703.5.8
Visual characters: line spacing135 to 170 percent of character height703.5.9
Raised characters: reliefAt least 1/32 in above the background703.2
Raised characters: case and styleUppercase only; sans serif; not italic, oblique, script, highly decorative or unusual703.2
Raised characters: height5/8 in minimum to 2 in maximum, measured on an uppercase I (1/2 in minimum where separate raised and visual characters carry the same information)703.2
Raised characters: strokeMaximum 15 percent of character height703.2
Raised characters: spacing1/8 in minimum, and 4 times the stroke width maximum; 3/8 in minimum from borders and decorative elements703.2
Raised characters: line spacing135 to 170 percent of raised character height703.2
BrailleDuplicates the raised characters; at least 3/8 in below the text703.3
Installation heightBaseline of the lowest tactile character at least 48 in above the floor; baseline of the highest at most 60 in703.4
Installation positionLatch side of a door; the inactive leaf of double doors with one active leaf; to the right of the right-hand door where both leaves are active; the nearest adjacent wall where there is no latch-side wall space703.4
Clear floor spaceAt least 18 in by 18 in, centered on the tactile characters, beyond the arc of a door swinging from closed to 45 degrees703.4
PictogramsField at least 6 in high, with no characters or braille inside it; text descriptor directly below the field; non-glare, light on dark or dark on light703.6

Two of those are worth borrowing outside their scope, because they describe real failures rather than legal ones: a text descriptor under any pictogram, and a non-glare finish on anything laminated.

Letter height from distance applies the rate, and Signs is the chapter.

Contrast thresholds

WhatThresholdLevelSection
Text and images of text4.5:1AAWCAG 2.1 SC 1.4.3
Large-scale text3:1AAWCAG 2.1 SC 1.4.3
Text, enhanced7:1AAAWCAG 2.1 SC 1.4.6
Large-scale text, enhanced4.5:1AAAWCAG 2.1 SC 1.4.6
Parts of a graphic needed to understand the content; component states3:1AAWCAG 2.1 SC 1.4.11
"Large scale" meansAt least 18 point, or 14 point bold (about 24 px and about 18.5 px)WCAG 2.1 SC 1.4.3
Text spacing a reader may impose without losing contentLine height 1.5; paragraph spacing 2; letter spacing 0.12; word spacing 0.16, each as a multiple of the font sizeAAWCAG 2.1 SC 1.4.12
Use of colorColor is not the only visual means of conveying information, indicating an action, prompting a response or distinguishing an elementAWCAG 2.1 SC 1.4.1

Definition Publisher: W3C Web Accessibility Initiative. Ratios are not rounded up: the W3C's own explanation says 4.499:1 does not meet the 4.5:1 threshold, and WebAIM's worked example of a gray at 4.47:1 against white fails. Exempt under 1.4.3: incidental text (inactive components, pure decoration, text not visible, text in a picture with significant other visual content) and logotypes.

What the ratio does not cover. WebAIM states that WCAG gives no guidance for gradients, semi-transparent colors or background images, and recommends testing the area of lowest contrast. The formula has no input for stroke weight, paper, glare, room light or viewing distance. Contrast and color has the full list, and Contrast ratio does the arithmetic.

Which version applies where, because two federal rules differ: the Revised 508 Standards, for federal electronic content, incorporate WCAG 2.0 Level A and AA by reference; the Department of Justice's title II rule, for state and local government web content and mobile apps, requires WCAG 2.1 Level AA, with compliance dates extended by an interim final rule published April 20, 2026 to April 26, 2027 for entities serving 50,000 or more and April 26, 2028 for smaller entities and special district governments. The W3C states that WCAG 2.2 does not deprecate or supersede 2.1, and that 2.0, 2.1 and 2.2 are all existing standards. The criteria used in this manual are unchanged between 2.1 and 2.2.

Type ranges, with the disagreement shown

FigureValuePublished byCovers
Body text size, screenAt least an effective 16 pxU.S. Web Design System (GSA)Running text on a screen
Body text size, screen15 to 25 pxButterick, one practitionerWeb body text
Body text size, print10 to 12 pointsButterick, one practitionerPrint body text
Business card text6 to 8 pointsButterick, one practitionerBusiness cards
Line length (measure)45 to 90 characters, spaces includedU.S. Web Design System and Butterick, independentlyRunning text at about arm's length
Line length target for long text66 charactersU.S. Web Design SystemLong passages
Line height, long textAt least 1.5U.S. Web Design SystemRunning text on a screen
Line height, headings and one-or-two-line elements1 to 1.35U.S. Web Design SystemHeadings, short blocks
Line spacing, print120 to 145 percent of the point sizeButterick, one practitionerPrint body text
Word processor's "Single" line spacingAbout 117 percentButterick, one practitionerMicrosoft Word
All capsFine for less than one line; add 5 to 12 percent letterspacingButterick, one practitionerHeadings, labels, small sizes
All caps, discouragedHarder to read, read as shouting onlineDigital.gov (GSA)Web and document text
Point to pixel conversion1 pt is about 1.333 pxW3C, in SC 1.4.3Deciding which contrast threshold applies
Points to the inch72Butterick, and the ordinary conventionEverywhere
The disagreement

1.5 and 120 to 145 percent do not agree, and this manual does not pick one. The U.S. Web Design System's figure is for running text on a screen, where a reader may also be resizing the page; WCAG 1.4.12 uses 1.5 as the value a reader may impose. Butterick's 120-to-145 percent is for print, which is a fixed object read at a fixed distance. A flyer headline belongs to neither, and the federal guidance's own 1-to-1.35 band for one-or-two-line elements covers it. The default in Type you can read is 1.5 for a block of running text, with tighter spacing for headlines, said as a decision rather than as a rule.

On Butterick. Ten pages of Butterick's Practical Typography were read for this manual. Preference None of them cites a study, named research or data source for any numeric rule, and on his font-recommendations page he states his own position: as a designer of professional fonts, he asks whether he is biased and answers that of course he is. The reason this manual uses him anyway is that his numbers are the most specific free recommendations available, and on measure and roughly on line spacing they agree with a federal publisher. Where they agree, the figure is stated as a figure. Where only he says it, the manual says so.

What no source gives. A number of typefaces. A rule for serif against sans; the Nielsen Norman Group says only that with today's high-resolution monitors, serif type is fine. A minimum type size for a slide. A minimum letter height for a yard sign. A measured effect of better design on attendance.

Figures that move, and when to re-read them

  • The ADA title II web rule's compliance dates, April 26, 2027 and April 26, 2028, set by an interim final rule published April 20, 2026. Live when this manual was built.
  • Canva's and Adobe Express's prices, read 2026-11-13 and listed on What you can make it in.
  • The USPS physical standards, which are revised periodically, including the conflicting card maximum noted above.
  • The Copyright Office's AI report series, where Part 3 was still a pre-publication draft on 2026-11-13.

The next scheduled re-read of every source behind this manual is a year from the build date; the date is on the resource library.